Just How to Remove as well as Replace a Bath Tub.
Just How to Remove as well as Replace a Bath Tub.
Blog Article
The article listed below about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is pretty much entertaining. You should check this stuff out.
Setting up a tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably challenging project. If the old bathtub is conveniently easily accessible, the job can move speedily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the work and fit trying it. Rather than working with a professional to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require a professional plumber to make tube links.
This post will assist you mount a new bath tub in your shower room if you have currently purchased a brand-new tub and do not need to alter the arrangement of your previous water system pipelines.
Your tools and product list must comprise the following:
Planning for the Installation
To start with, the sustaining framework provided with the bath must be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be rather problematic because of the restricted gain access to that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will come from the pipelines. When the supply pipelines have actually been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to going on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Using both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub until the spirit level reviews degree.
To set up faucets, fit the bottom of the furthest adaptable faucet port to the proper supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the water supply as well as examine all joints as well as new pipework for leaks and tighten them if required. Fill up the bath tub as well as likewise check the overflow electrical outlet as well as the typical electrical outlet for leaks.
Finally, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub should wait until the bathtub has been made use of a minimum of when as this will certainly settle it right into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be linked to the tap finishes initially, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a rigid seal, causing the water to pass through the wall in between the bath and also the tiling, causing problems with moisture and possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your components as well as fittings. They are sold in tubes and cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the movement experienced when the bathtub remains in use. The sealant can break rather early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the marketplace. It is suggested to fit the tiles using waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our piece about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for spending some time to browse our post. Enjoyed reading our article? Please share it. Let other people check it out. Thanks so much for going through it.
Show Details Report this page